首 页供应产品无线充60W PoE电源
首 页 > 供应产品 > 无线充 > 60W PoE电源

60W PoE电源

型号:WC-PD60B120B

产品介绍

1.Product characteristics

  • Compliance with IEEE802.3at &IEEE802.3bt standard.
  • 48V~57V wide operating voltage range.
  • Maximum output power up to 60W; Rated output: 12V/5A.
  • The output ripple is less than 200 mV.
  • Conversion efficiency can be as high as 90% (input: 48V output)12V@5A).
  • Withovercurrent, short circuit, under voltage, surge andother excellent reliability and circuit protection.
  • PCBA standard size: 62mm*27mm*11mm
  • Input/Output: isolate 1500Vdc.
  • High reliability: The design meets the 5 million hour average failure interval.

2.Scope of application

  • Thin client
  • POS system
  • Digital signage
  • Health care □Lighting

3.Describe

The module is designed to extract power from conventional Class 5 to Class 6 Ethernet cable twisted pairs and meets the IEEE 802.3bt Power-Ethernet (PoE) standard.At the same time, the module allows the power supply category to select "Intermediate Overlap" and "End Overlap" power supply without distinguishing polarity.

Based on the IEEE 802.3bt standard, this paper establishes information connection about the connection status, device type, power consumption level of the receiving device PD, and then applies power supply to port compatible devices based on PSE to power the PD through ethernet.

This module DC/DC converter works in a wide input voltage range and low ripple low noise output.The DC/DC converter also has built-in output overload, output short circuit and overtemperature protection, and provides a 1500Vdc (input/output) electrical isolation.

4.Pin definition

Pin Name Describe
1 VA1 This input pin is used in conjunction with VA1 and connects to the centre tap of the transformer connected to pins 1& 2 of the RJ45 connector (RX) - it is not polarity sensitive.
2 VA2 This input pin is used in conjunction with VA2 and connects to the centre tap of the transformer connected to pins 3& 6 of the RJ45 connector (TX) - it is not polarity sensitive.
3 VB1 This input pin is used in conjunction with VB1 and connects to pin 4 & 5 of the RJ45 connector - it is not polarity  sensitive.
4 VB2 This input pin is used in conjunction with VB2and connects to pin 7 & 8 of the RJ45 connector - it is not polarity  sensitive.
5 Vout- 5,6 is the negative output of the PD.
6 Vout- 5,6 is the negative output of the PD.
7 Vout+ 7,8 is the positive output of the PD.
8 Vout+ 7,8 is the positive output of the PD.
9,10 NC Welding fixed foot.

5. Electrical characteristics

5.1 Absolute maximum rating parameter

No Parameter Symbol MIN MAX Units
1 DC Voltage VCC 48 57 V
2 DC Voltage Surge 1ms VSURGE -0.6 80 V
3 Working temperature TS -40 80

*Exceeding the above rating may cause permanent damage to the product.Functional operations under these conditions are not recommended.

5.2 Recommended working conditions

No Parameter Symbol MIN TYP MAX Units
1 Input voltage VIN 42 48 57 V
2 Low Voltage Lock VLOCK  37 - - V
3 Working temperature TOP -40 25 80

*Applicable only to WC-PD60B120B maximum operating temperature.

5.3 DC Characteristic

No Parameter Symbol MIN TYP MAX Units Test Opinions
1 Standard Output Voltage VDC 11.5 12.0 12.2 V VIN=48V
2 Output Current(VIN=48V) PWR - 5 6 A Wide voltage input 48-57V
3 Power adjustment rate VLINE - 0.1 - % @50% Load
4 Load Adjustment Rate VLOAD - 1 - % @VIN=48V
5 Ripple Output Noise VRN - 150 250 mVp-p @Maximum Load
6 Minimum Load RLOAD 10 - - mA  
7 Short circuit duration TSC - - sec  
8 Efficiency (load 80%) EFF 85 90 - %  
9 Isolation Voltage (I/O) VISO - - 1500 VPK  
10 Temperature coefficient Tc - 0.02 - % Per ℃
11 Efficiency Tr - 150 250 ms VIN=48V
VOUT=max

1: Typical number is 25 C, nominal voltage is 48V, for auxiliary design only.

2: Output ripple and noise can be reduced by an external filter, see the application instructions.

3: If operated under the specified minimum load, the module emits audible noise and may cause PSE malfunction.

6 Power Classification

WC-PD60B120B uses IEEE802.3at standard and runs with Class 7 (60W) power rating by default.

Define criteria Cable requirements Grading parameters Power Supply Characteristics
IEEE802.3at
(PoE)
CAT5 cable or
CAT6 cable
Maximum power required for Class4 devices is 13W~25.5W The DC voltage ranges from 42 to 57V, with a typical value of 48V.
Typical operating current is 10~600mA; typical output power: 30W;
Class4 rating supported by electrical equipment
IEEE802.3bt
(PoE++)
CAT5 cable or
CAT6 cable
Maximum power required for Class5 devices is 40W The DC voltage ranges from 48 to 57V, with a typical value of 52V.
Typical operating current is 10~1300mA; typical output power: 62W
The maximum power required for Class6 devices is 51W
The maximum power required for Class7 devices is 62W
The maximum power required for Class8 devices is 71W