1.Product characteristics
- Compliance with IEEE802.3at &IEEE802.3bt standard.
- 44V~57V wide operating voltage range.
- Maximum output power up to 60W; Rated output: 24V/2.5A.
- The output ripple is less than 200 mV.
- Conversion efficiency can be as high as 87% (input: 48V output)12V@2.5A).
- Withovercurrent, short circuit, under voltage, surge andother excellent reliability and circuit protection.
- PCBA standard size: 62mm*27mm*15mm
- Input/Output: isolate 1500Vdc.
- High reliability: The design meets the 5 million hour average failure interval.
2.Scope of application
- Thin client
- POS system
- Digital signage
- Health care
- Lighting
3.Describe
The module is designed to extract power from conventional Class 5 to Class 6 Ethernet cable twisted pairs and meets the IEEE 802.3bt Power-Ethernet (PoE) standard.At the same time, the module allows the power supply category to select "Intermediate Overlap" and "End Overlap" power supply without distinguishing polarity.
Based on the IEEE 802.3bt standard, this paper establishes information connection about the connection status, device type, power consumption level of the receiving device PD, and then applies 60W power supply to port compatible devices based on PSE to power the PD through ethernet.
This module DC/DC converter works in a wide input voltage range and low ripple low noise output.The DC/DC converter also has built-in output overload, output short circuit and overtemperature protection, and provides a 1500Vdc (input/output) electrical isolation.
4.Pin definition
| Pin | Name | Describe |
| 1 | VA1 | This input pin is used in conjunction with VA1 and connects to the centre tap of the transformer connected to pins 1& 2 of the RJ45 connector (RX) - it is not polarity sensitive. |
| 2 | VA2 | This input pin is used in conjunction with VA2 and connects to the centre tap of the transformer connected to pins 3& 6 of the RJ45 connector (TX) - it is not polarity sensitive. |
| 3 | VB1 | This input pin is used in conjunction with VB1 and connects to pin 4 & 5 of the RJ45 connector - it is not polarity sensitive. |
| 4 | VB2 | This input pin is used in conjunction with VB2and connects to pin 7 & 8 of the RJ45 connector - it is not polarity sensitive. |
| 5 | Vout- | 5,6 is the negative output of the PD. |
| 6 | Vout- | 5,6 is the negative output of the PD. |
| 7 | Vout+ | 7,8 is the positive output of the PD. |
| 8 | Vout+ | 7,8 is the positive output of the PD. |
| 9,10 | NC | Welding fixed foot. |
5. Electrical characteristics
5.1 Absolute maximum rating parameter
| No | Parameter | Symbol | MIN | MAX | Units |
| 1 | DC Voltage | VCC | 48 | 57 | V |
| 2 | DC Voltage Surge 1ms | VSURGE | -0.6 | 80 | V |
| 3 | Working temperature | TS | -40 | 80 | ℃ |
*Exceeding the above rating may cause permanent damage to the product.Functional operations under these conditions are not recommended.
5.2 Recommended working conditions
| No | Parameter | Symbol | MIN | TYP | MAX | Units |
| 1 | Input voltage | VIN | 42 | 48 | 57 | V |
| 2 | Low Voltage Lock | VLOCK | 37 | - | - | V |
| 3 | Working temperature | TOP | -40 | 25 | 80 | ℃ |
*Applicable only to WC-PD60B240A maximum operating temperature.
5.3 DC Characteristic
| No | Parameter | Symbol | MIN | TYP | MAX | Units | Test Opinions |
| 1 | Standard Output Voltage | VDC | 23 | 24 | 24.7 | V | VIN=48V |
| 2 | Output Current（VIN=48V） | PWR | - | 5 | 6 | A | Wide voltage input 48-57V |
| 3 | Power adjustment rate | VLINE | - | 0.1 | - | % | @50% Load |
| 4 | Load Adjustment Rate | VLOAD | - | 1 | - | % | @VIN=48V |
| 5 | Ripple Output Noise | VRN | - | 150 | 250 | mVp-p | @Maximum Load |
| 6 | Minimum Load | RLOAD | 10 | - | - | mA | |
| 7 | Short circuit duration | TSC | - | - | ∞ | sec | |
| 8 | Efficiency (load 80%) | EFF | 85 | 90 | - | % | |
| 9 | Isolation Voltage (I/O) | VISO | - | - | 1500 | VPK | |
| 10 | Temperature coefficient | Tc | - | 0.02 | - | % | Per ℃ |
| 11 | Efficiency | Tr | - | 150 | 250 | ms | VIN=48V VOUT=max |
1: Typical number is 25 C, nominal voltage is 48V, for auxiliary design only.
2: Output ripple and noise can be reduced by an external filter, see the application instructions.
3: If operated under the specified minimum load, the module emits audible noise and may cause PSE malfunction.
6 Power Classification
WC-PD60B120B uses IEEE802.3at standard and runs with Class 7 (60W) power rating by default.
| Define criteria | Cable requirements | Grading parameters | Power Supply Characteristics |
| IEEE802.3at （PoE） |
CAT5 cable or CAT6 cable |
Maximum power required for Class4 devices is 13W~25.5W | The DC voltage ranges from 42 to 57V, with a typical value of 48V. Typical operating current is 10~600mA; typical output power: 30W; Class4 rating supported by electrical equipment |
| IEEE802.3bt （PoE++） |
CAT5 cable or CAT6 cable |
Maximum power required for Class5 devices is 40W | The DC voltage ranges from 48 to 57V, with a typical value of 52V. Typical operating current is 10~1300mA; typical output power: 62W |
| The maximum power required for Class6 devices is 51W | |||
| The maximum power required for Class7 devices is 62W | |||
| The maximum power required for Class8 devices is 71W |
